Epoxy resin is a crafting material. It is very popular among crafters due to its strength, clarity, and ability to work with it. To new users, working with epoxy resin may sound quite challenging, but with the proper equipment and following the instructions given below, anyone can make beautiful resin pieces. For beginners, Bond Craftor’s two part epoxy resin is ideal since it is easy to mix and guarantees excellent results with every application. This article will learn the basic procedures that are necessary for your first resin project to be successful.

Step 1: Prepare Your Work Area

Organization of your work area is important for any resin project. Select a clean, dry, and dust-free environment. So that anybody can comfortably work without any interruptions. The effect is that the resulting area may have an uneven surface. It will not allow the further laying of a layer of resin, or a layer of resin is laid in a thin layer, and this is bad for further proper curing of the layer. Spread some disposable plastic or newspaper on the floor so that if any resin drops it does not harm the floor.

Step 2: Measure and Mix the Resin and Hardener

Bond Craftor's two-part epoxy resin requires mixing the resin and hardener in a precise 1:1 ratio. The measurements have to be precise to allow the resin to cure as it should. Take two different measuring cups and measure the same quantity of resin and hardener into the other measuring cup. When one part is in the mixing cup with the other, stir the mixture for at least 3-4 minutes. It is crucial to scrape the cup sides and the bottom as you stir to guarantee that both the resin and the hardener are mixed well.

Step 3: Customize Your Resin (Optional)

It is also possible to add other substances like pigments, glitter, or even other additional components that have a specific color. Bond Craftor’s epoxy resin can be easily mixed with mica powders, alcohol inks, or resin dyes. If you’re adding color or some other effects, pour the required quantity of pigment into the resin and mix it properly.

Step 4: Pour the Resin into the Mold

Here comes the most exciting part of the process, the application of the resin into your mold. In case you observe any bubbles as soon as you pour the resin, you can use a heat gun or a torch and gradually move them over the surface of surface of the resin. The heat will help to burst the bubbles and give a glass-like surface to the finished product. Use heat with care because too much heat will cause the resin to cure in the wrong way.

Step 5: Let the Resin Cure

After pouring into the mold, allow it to cure. Bond Craftor two-part epoxy resin cures in 24-48 hours depending on the temperature and humidity of the working environment. They should ensure that the mold is placed in a flat and clean place during this time to prevent interferences with the curing process. It is also important not to manipulate mold in any way while the resin is in the process of solidifying. This step involves a lot of waiting.

Step 6: Demolish and Finish Your Project

Once the resin has cured it is time to de-mold your creation! To detach the resin piece from the mold, care should be taken and the mold should either be bent a little or tapped lightly. As a general rule, with Bond Craftor's two-part epoxy resin, the molded object will be easily released with little or no force. If they are sharp, then with the help of sandpaper or a file you can make them smoother.

Step 7: Clean Up Your Tools

Lastly, always wash your tools and also clean the working area. The use of isopropyl alcohol will be appropriate for washing out any residual resin from your mixing cups stir sticks, and molds. Any resin waste should be disposed of correctly as uncured resin is toxic to the environment.

Conclusion

It is always exciting to use Bond Craftor's two-part epoxy resin for the first time if you follow the right procedures. These basic steps of measuring and mixing, pouring and curing, help even the novices to achieve stunning resin art. Resin crafting is not a difficult skill to master and with time and effort, anyone can create beautiful art pieces from resin. It is a perfect option for making jewelry, art, and other items, including those that are more practical, if you use Bond Craftor epoxy resin.